Siemens WM14T7P9DN Instruction Manual And Installation Instructions Download

Page: 34 / 46

Operating the appliance

Adding laundry

After starting the programme, you can

add or remove laundry if necessary.
To do this, touch the control panel

‹

The indicator flashes. The machine is

paused and checks whether it is

possible to add laundry.
If the display

goes out, it is possible

to add laundry. The door is then

unlocked and can be opened.

To continue the programme. touch

‹

again. The programme continues

automatically.

Notes

■

Do not leave the door open for too

long when adding laundry as water

from the laundry may leak out.

■

For safety reasons, the door remains

locked when the water level or

temperature is high, or while the

drum is turning, and it is not possible

to add laundry during this time.

Follow the information on the display

panel.

■

It is possible to add laundry during

the sensoFresh

programme.

■

The load display is not active during

reloading.

Changing the programme

If you have started the wrong

programme by mistake, you can

change the programme as follows:

Touch the control panel

‹

Select another programme.

And touch

‹

again.The new

program starts from the beginning.

Note:

When cancelling programmes

that use active oxygen, the door will

remain locked for up to 25 minutes until

there is no longer any active oxygen in

the drum.

Switch the appliance on again if

necessary. The

and

symbols will

flash. If the symbols are off, the door

can be opened.

Cancel the programme

For programs at high temperature:

Touch the control panel

‹

To cool the laundry: Select

Rinse

And touch

‹

again.

For programmes at low temperatures:

Touch

‹

Select

Spin

Empty

And touch

‹

again.

Note:

When cancelling programmes

that use active oxygen, the door will

remain locked for up to 25 minutes until

there is no longer any active oxygen in

the drum.

Switch the appliance on again if

necessary. The

and

symbols will

flash. If the symbols are off, the door

can be opened.

Programme end during rinse

hold

The

‹

indicator flashes in the display

panel, and the preset spin speed and

remaining programme length are

displayed for the selected programme.

Continue the programme by:

■

Touching

‹

on the control panel or

■

Changing the spin speed and then

touching

‹

■

Selecting the Less iron

setting

and then touching

‹

■

Turning the programme selector to

Empty

and then touching

‹

Programme end

End

lights up in the display panel and

the

‹

and

displays are off.

Note:

If the

display flashes, this

informs you to run the

Drum Clean

programme or any other programme at

Summary of Contents for WM14T7P9DN















































Search results

Summary of Contents for WM14T7P9DN

Reviews:

Related manuals for WM14T7P9DN

Brands by name

Popular brands

Siemens WM14T7P9DN, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WM14T7P9DN

Reviews:

Related manuals for WM14T7P9DN

Brands by name

Popular brands