1
Safety instructions
The washing machine is heavy take care when lifting it.
Warning: Frozen hoses may tear/burst. Do not install the washing machine in an area where
there is a risk of frost or outdoors.
Do not hold onto protruding parts (e.g. loading door) when lifting. Washing machine may
be damaged.
Before transporting the appliance, always drain dispensers.
a
Page 8
In addition to the safety information listed here, the local water and electricity supplier may
have special requirements.
If in doubt, have the appliance connected by a technician.
Lay hoses and cables in such a way that there is no risk of stumbling.
Environmental disposal
Dispose of packaging in an environmentally friendly manner.
This appliance has been identified in accordance with the European Directive 2002/96/EG
on Waste Electrical and Electronic Equipment (WEEE).
The Directive specifies the framework for an EU-wide valid return and recycling of waste
appliances.
Installation area
Stability is important to prevent the machine from moving!
The installation area must be firm and level.
Soft floors/floor coverings are not suitable.
If installing the appliance on a base
Always
secure the washing machine feet with retention plates *.
* Order no. WMZ 2200, WX 9756, CZ 110600, Z 7080X0
If installing the appliance on a wooden joist ceiling
If possible, install the washing machine in a corner.
Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
Always
secure the washing machine feet with retention plates.
* Order no. see above
Built-under/Built-in appliance
Build-under/Build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
60 cm cavity width required.
Install washing machine only under a continuous worktop connected firmly to the adjacent
cupboards.
Built-under
Risk of electric shock!
Instead of the appliance cover panel, it is
essential
to have a technician fit a sheet metal
cover *.
* Order no. WMZ 2043, WZ 20430
60 cm cavity width required.
2
Scope of delivery
depending on model
not included in product package:
When drainage is into a siphon, a Ø 2440 mm hose clip (specialist outlet) is also required.
a
Water connection, Page 4
Useful tools:
Spirit level for aligning the washing machine.
Size 13 socket wrench:
for loosening the transportation protection devices
a
Page 3
and
size 17: for aligning the appliance feet.
a
Page 5
Hose and cable lengths
depending on model
Connection on left side
or
Connection on right side
Note: If the hose holders are used, the possible hose lengths are reduced!
Available from dealer/customer service:
Extension for Aqua-Stop or cold water inlet hose (approx. 2.50 m).
Order no. WMZ2380, WZ10130, CZ11350, Z7070X0
Longer supply hose (approx. 2.20 m), for standard model.
Spanner
(depending on model)
Power cord
Water supply
Water drainage
Elbow
for securing the
drainage hose
Covers
with hose holder
Aqua Stop
Aqua-Secure
Standard
~ 140 cm
~ 95 cm
~ 120 cm
~ 130 cm
~ 100 cm
~ 135 cm
0
m
ax
. 1
0
0
c
m
Humidity in the drum
is caused by the final
inspection.
3
Remove transportation protection devices
Before using the appliance for the first time, remove the
4 transportation protection devices completely and keep in a safe
place.
If the appliance is to be transported at a later date, re-install the
transportation protection devices prevents damage to the machine.
a
Page 6
Keep screw and sleeve together.
1.
Take hoses (depending on model) out of the
holders and the elbow. Remove the elbow.
2.
Loosen and remove all 4 transportation lock screws.
3.
Take the power cord out of the holders.
Remove sleeves.
4.
Insert covers and lock firmly by pressing on the locking hook at the top. Insert hose holder.
5.
Secure hoses in the hose holders.
4
Water connection
depending on model
Risk of electric shock!
Do not immerse Aqua-Stop safety device in water (contains
an electric valve).
To prevent leakage or water damage, follow the instructions in this chapter!
Caution:
The washing machine must only be operated with cold tap water.
Do not connect to the mixer tap of an unpressurised hot-water apparatus.
Use only the supplied inlet hose or one purchased from an authorised specialist outlet,
not a used one!
If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Caution:
do not kink, crush, modify or sever
(strength is no longer guaranteed).
Optimum water pressure in the mains: 1001000 kPa (110 bar)
When the tap is turned on, the water flow is at least 8l/min.
If the water pressure is higher, install a pressure reducing valve.
Model:
Aqua-Stop
Aqua-Secure
Standard
1.
Connect water inlet hose to a 3/4" = 26.4 mm tap.
Caution:
Tighten plastic screw-fittings by hand only.
2.
Carefully turn on the tap and check that the connection
points are not leaking.
Caution:
Screw connection is under water pipe
pressure.
Water drainage
Water drainage hose:
Caution:
Do not bend or pull.
Height difference between installation area and outlet:
0 max. 100 cm
Drainage into a washbasin:
Caution:
Secure the drainage hose to prevent it from slipping out of the
sink.
Caution:
The plug must not block the drain of the wash basin. When the
water is being pumped out of the washing machine, check that the water
drains away quickly enough. The end of the drainage hose must not be
immersed in the drained water! Risk of water being drawn back into the
washing machine!
Drainage into a siphon:
Caution:
Connection point must be secured with hose clip, Ø 2440 mm
(specialist outlet).
.
Drainage into a plastic pipe with rubber sleeve or into a gully:
Caution:
Secure the drainage hose to prevent it from slipping out of the
sink.
max.
90°
max.
90°
min.
10 mm
min.
10 mm
3/4
3/4
5
Alignment
Loud noise formation, intense vibrations and wandering may be due to incorrect
alignment!
Align washing machine with spirit level
1.
Loosen lock nut in a clockwise direction with a wrench.
2.
Change height by rotating the appliance feet.
Caution:
All four feet must be firmly on the floor.
The washing machine must not wobble!
Check alignment of the washing machine with a spirit level and, if
required, correct.
3.
Tighten the lock nut against the housing.
Grip the foot and do not adjust the height.
Caution:
The lock nuts on all four appliance feet must be screwed tightly
against the housing!
Electrical connection
ʑ
Connect the washing machine to an alternating current via a correctly installed
earthed socket only.
ʑ
The mains voltage and voltage specifications on the washing machine (appliance
rating plate on the rear of the appliance) must match.
ʑ
Connected load as well as required fuse are indicated on the appliance rating plate.
ʑ
Ensure that:
the mains plug and socket match,
the cable cross-section is adequate,
the earthing system has been installed correctly.
ʑ
A damaged power cord may be replaced by an electrician only.
A replacement mains cable can be obtained from customer service.
ʑ
Do not use multiple plugs/couplings or extension cables.
ʑ
In the event that an earth leakage circuit breaker is to be used, only use types
marked with the following symbol:
.
Only this symbol can guarantee compliance with all current regulations.
ʑ
Mains plug:
Do not insert/pull out with damp hands.
Do not pull by tugging the power cord.
Never pull it out during operation.
m
ax
. 1
2
m
m
6
Transportation, e.g. if moving house
1.
Before transporting the washing machine:
1.
Turn off the tap.
2.
Drain any residual washing solution.
a
Page 12
3.
Release the water pressure in the supply hose.
a
Page 12
4.
Isolate the washing machine from the power supply.
5.
Remove the hoses.
6.
Drain dispensers.
a
Page 8
2.
Installing transportation protection devices:
1.
Remove covers and keep
in a safe place.
If required, use a
screwdriver.
2.
Insert all 4 sleeves.
Clamp mains cable on the
holders. Insert and tighten
the bolts.
3.
Before switching on the appliance again,
remove the transportation protection devices!
a
Page 3
To prevent unused detergent from flowing into the outlet during the first wash: Pour 1 litre of
water into dispenser
B
/
C
and start the
Empty
programme.
Aqua-Stop warranty
For appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty we shall pay damages under the following conditions:
1.
If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
2.
The liability warranty applies to the service life of the appliance.
3.
A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (original accessory).
Our warranty does not apply to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
4.
Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
7
Technical specifications
ʑ
Dimensions (width x depth x height)
60 x 59 x 85 cm
ʑ
Weight
63 83 kg
depending on model
ʑ
Mains connection
Nominal voltage 220 240 V, 50 Hz
Nominal current 10 A
Nominal power 2300 W
ʑ
Water pressure
100 1000 kPa (1 10 bar)
0
8
1
1
/
9
0
0
0
5
5
0
6
3
4
*
5
5
0
6
3
4
*
Manufacturer
a
Operating instructions
