Siemens WM T Series Instruction Manual And Installation Instructions Download

Page: 31 / 54

Operating the appliance

If you turn the programme selector or

touch the control panel while the

childproof lock is active, the

3 sec

indicator flashes briefly and a signal

sounds. The programme runs through

to the end unchanged.

Notes

■

The childproof lock can be activated

regardless of the appliance's status.

■

The childproof lock remains active,

even once the washing machine has

been switched off.

■

If the appliance is switched off while

the programme is running and the

childproof lock has been activated,

the programme will resume when the

appliance is switched back on.

Adding laundry

After starting the programme, you can

add or remove laundry if necessary.
To do this, touch the control panel

The indicator flashes. The machine is

paused and checks whether a top-up is

possible.
If the display

goes out, a top-up is

possible. The door is then unlocked and

can be opened.

To continue the programme. touch

again. The programme continues

automatically.

Notes

■

Do not leave the door open for too

long when adding laundry as water

from the laundry may leak out.

■

For safety reasons, the door remains

locked when the water level or

temperature is high, or while the

drum is turning, and it is not possible

to add laundry during this time.

Follow the information on the display

panel.

■

The load display is not active during

reloading.

Changing the programme

If you have started the wrong

programme by mistake, you can

change the programme as follows:

Touch the control panel

Select another programme.

And touch

again.The new

program starts from the beginning.

Cancel the programme

For programs at high temperature:

Touch the control panel

To cool the laundry: Select

Полоскание

(Rinse)

And touch

again.

For programmes at low temperatures:

Touch

Select

Отжим

(Spin)

Слив

(Drain/Empty)

And touch

again.

Programme end during rinse

hold

The

indicator flashes in the display

panel, and the preset spin speed and

remaining programme length are

displayed for the selected programme.

Continue the programme by:

■

Touching

on the control panel or

■

Changing the spin speed and then

touching

■

Selecting the

Антисмин

. (Less

iron)

setting and then touching

■

Turning the programme selector to

Слив

(Drain/Empty)

and then

touching

Programme end

End

lights up in the display panel and

the

and

displays are off.

Summary of Contents for WM T Series























































Search results

Summary of Contents for WM T Series

Reviews:

Related manuals for WM T Series

Brands by name

Popular brands

Siemens WM T Series, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WM T Series

Reviews:

Related manuals for WM T Series

Brands by name

Popular brands