background image

Faults and what to do about them       

en

43

Information on the display panel

Faults and what to do about them

Information

Cause/Remedy

Õ

Flashes fast + signal

: The door was opened and the water level is too high. 

Close the door, continue the programme with 

Start/Reload

 button or select 

Drain

 programme.

Flashes slowly

: The door lock temperature is too high to open the door. Wait 

approx. 30 seconds until the door lock cools down.

Hot

The door cannot be opened after the drying programme due to the high tempera-

ture. The cooling process continues until the display disappears, after which the 

door can be opened.

|

Flashes

 (no water supply): Tap turned on? Water inlet filter blocked? Clean 

the water inlet filter. 

~

 Page 42

Water hose kinked or blocked?

Lights up

 (low water pressure): For information only. This will not affect the 

programme progress. The programme duration is extended.

E:18

Drain pump blocked; clean the drain pump. Clean the drainage hose on the siphon. 

E:32

Alternating display with 

End

 when programme is finished: unbalance problem, 

spinning phase is aborted.

E:95

Alternating display with 

End

 when programme is finished: no water detected in 

drying phase, may get bad drying result.

Other displays

Turn the programme selector to 

$

 

Off

. The appliance is switched off. Wait 5 s and 

switch on again. If the display is indicated again, call customer service. 

Faults

Cause/Remedy

Water is running out.

Correctly attach/replace drainage hose.

Tighten screw-fitting on the supply hose.

Water not flowing in.
Detergent not dispensed.

Start/Reload

 not selected?

Tap not open?

Filter blocked? Clean the filter

~

 Page 42

Supply hose kinked or jammed?

The washer dryer door 

cannot be opened.

Safety function active.

Note:  

For safety reasons, the washing machine door remains locked 

when the water level or temperature is high (See 

~

 Cancel the pro-

gramme 

~

 Page 30

) or while the drum is rotating.

- - - -

 (Rinse stop = without final drain/spin) selected? 

Can be opened with emergency lock release only? 

~

 Page 42

Childproof lock active? Deactivate. 

~

 Page 30

Programme does not 

start.

Start/Reload

 or 

û

 

Finish in

 selected?

Door closed?

Childproof lock active? Deactivate. 

~

 Page 30

Summary of Contents for WD15G422GB

















































Reviews: