manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 242

Service only

13.4 Messages and troubleshooting measures

Events and faults

13 - 10

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

13.4 Messages and troubleshooting measures

The recommended troubleshooting measures are listed in the fol-
lowing tables. If an error persists even after you have performed the 
recommended measures, please contact our hotline:

Siemens VDO Automotive AG
Commercial Vehicles
OEM-Support
D-78052 Villingen-Schwenningen

Attention

Please do not attempt to open or modify the device!

A defective DTCO 1381 or the respective system component must be 
inspected and possibly replaced in its entirety.

Jürgen Daucher
Tel.:

+49 (0) 7721 - 67 31 96

Fax:

+49 (0) 7721 - 67 27 29

E-Mail:

[email protected]

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands