manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 205

Service only

Regularly inspection

11.2 Calibration instructions

Edition 07/2007

Technical Description DTCO 1381

11 - 5

TD00.1381.00 13

2 102

11.2 Calibration instructions

The CR (EEC) 3821/85, annex I B, defines the criteria for the cali-
bration of EC recording equipment.

11.2.1 Legal requirements for when to perform a calibration

The recording equipment must be calibrated:

•

after every installation

•

during every regularly inspection

11.2.2 Access to the calibration functions

Before activation of the DTCO 1381 to be EC recording equipment, it 
will be possible to access the calibration functions through the cali-
bration interface, the CAN bus diagnosis, or the K-Line diagnosis 
without a workshop card.

After activation of the DTCO 1381, it will be possible to access the 
calibration functions only with a workshop card.

Note the legal provisions applicable in your country and check, how 
the calibration must be performed and whether further tests of the 
EC recording equipment are prescribed.

The accredited workshop must guarantee that the calibration is per-
formed only via one interface selected before and that the cali-
bration functions of the other interfaces are deactivated.

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands