manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 188

Service only

10.3 Testing equipment

First calibration

10 - 10

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

10.3 Testing equipment

The calibration is performed with a appropriate test equipment; for 
example, the Siemens VDO SDS test devices MTC 1602.04 or 
ATC 1601.26.

Fig. 10 - 1: Siemens VDO SDS test devices MTC 1602.04 / ATC 1601.26

For the calibration with the Siemens VDO SDS test devices the fol-
lowing testing equipment must be available:

(1)

BTC 

test software, version DTCO 1381 or higher

(2)

Mount 

(MTC/ATC) with firmware version DTCO 1381

(3)

Programming cable

(4)

Diagnosis cable DTCO 1381

DTCO 1381 testing and programming software

 

(without figure)

Authentication

(5)

Workshop card

An approved recording equipment manufacturer, vehicle man-
ufacturer, installer, or a workshop uses its card to identify itself 
to the DTCO 1381, enabling saving of activities under this 
identity. 

After a positive authentication, the workshop card enables 
activation; pairing with the KITAS 2171; calibration, and 
testing of the DTCO 1381; the downloading of data; and 
transfer, test, and test drives.

2

4

3

5

1

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands