Siemens TX-I/O User Manual Download Page 85

Page: 85 / 94

85 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Hardware

23.09.2010

8.3

Labeling and Addressing Devices

8.3.1

Flow and Allocation of the Labelling

Depending on the project work flow and organization of the goods flow, the labels

–

are supplied with the devices to install

–

are used when taking them into commission at the system site.

8.3.2

Labeling the I/O Modules

The information applied at the following positions is used for unique identification of
each I/O module and its connections:



Module front

–

Module type and symbols for the display and control elements

–

Insertable label, can be freely labeled



Address key

–

Address numbers from 1...120

The insertable labels for the I/O modules can be freely labeled.

A4 sheets with the corresponding divisions and perforations can be ordered

under the order number TXA1.LA4.

These sheets can be printed with the easy-to-use Excel file

IoLabel.xls

The module address and the function of each I/O point can be printed on the labels
created in this way.

A function is integrated into the TX-I/O tool that enables the label sheets to be
automatically printed in accordance with the generated module assignment.

The connection terminals have only general names since the I/O points can have
different functions.



The electronic unit has a removable transparent cover (label holder) into which

the label can be inserted (A, C).



The modules can also be operated without this 'cover' (B).

Inserting the label

Removing the cover

Assembly

1056

Different flows

Labeling positions

Labels

Connection terminals

Inserting the labels

Summary of Contents for TX-I/O































































































Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands

Siemens TX-I/O, User Manual

Search results

Summary of Contents for TX-I/O

Reviews:

Related manuals for TX-I/O

Brands by name

Popular brands