Siemens Synco living Operating Instructions Manual Download Page 87

Page: 87 / 100

87 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Service

23.08.2008

Replace batteries

To ensure trouble-free operation of the battery-powered devices, replace the
batteries as soon as they are close to exhaustion.

Avoid complete discharge of batteries, as otherwise batteries may
leak. For this reason, replace the battery as soon as the display tells
you to.

Room unit QAW910, room sensor QAA910 and
meteo sensor QAC910

Have 2 new Alkaline AA batteries
ready for insertion (LR6 / 1.5 V).

Remove the battery compartment
cover.

2701Z23

707

Remove the exhausted batteries.

Insert the new batteries. Ensure that
polarity is correct!

707Z

2707Z

Replace the battery compartment
cover.

Dispose of the old batteries in compli-
ance with environmental regulations.

2707Z

2701Z22

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands