Siemens Synco living Operating Instructions Manual Download Page 80

Page: 80 / 100

80 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Room unit QAW910

23.08.2008

Room unit QAW910

Operation

All operating elements are arranged
on the front of the unit. The function
button is located in the battery com-
partment. The room unit communi-
cates via radio signals and has no
connection terminals.

The settings made on the room unit
only have an impact on the room to
which the room unit is assigned.
They have no influence on any other
rooms.

The settings made on the room unit
are automatically synchronized with
the settings of the central apartment
unit.

Room operating modes

By pressing the

Mode

button, you can select the required room

operating mode.

The display shows the hourglass symbol which disappears again as
soon as the central apartment unit and the room unit have adopted
the new settings.

AUTO

The room is controlled in accordance with the time program
and the special day program.

MAN

The room is maintained at the Comfort setpoint.

MAN

The room is maintained at the Precomfort setpoint.

MAN

The room is maintained at the Economy setpoint.

MAN

The room is maintained at the Protection setpoint.

Overriding by the central apartment unit to maintain the
Comfort setpoint.

Overriding by the central apartment unit to maintain the
Precomfort setpoint.

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands