Siemens Synco living Operating Instructions Manual Download Page 58 | Manualshive

Page: 58 / 100

background image

58 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Changeover to electric immersion heater

Select whether in summer operation the DHW should be heated by the elec-
tric immersion heater.

Yes

When the plant switches to summer operation (refer to page 30),
the DHW is heated by the electric immersion heater. This means
that heat generation can be switched off in the summer.

No

DHW is heated by the heat source in the summer also. This means
that heat generation in the summer remains in operation (emer-
gency operation).

If no charging pump is defined, the electric immersion heater is al-
ways released (no charging via the heat source).

Main menu > DHW > Settings > Change el imm heat:

Factory setting

Yes

Your setting

No

Yes

Supervision of the DHW temperature

The controller is capable of continuously monitoring the DHW temperature. If
the DHW temperature exceeds “Max temp alarm“, or falls below “Min temp
alarm“, an error message is displayed.

When using setting “----“, temperature supervision is deactivated.

Main menu > DHW > Settings > Max temp alarm:

Main menu > DHW > Settings > Min temp alarm:

Max temp alarm

Min temp alarm

Factory setting

---- (inactive)

---- (inactive)

Your setting

«
...
56
57
58
59
60
...
»

Summary of Contents for Synco living





































































































Reviews:

No comments

Related manuals for Synco living

Brand: Parker Pages: 30

Brand: VAT Pages: 22

Brand: FAAC Pages: 14

Brand: Safeline Pages: 8

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: Fanimation Pages: 2

Brand: M2M Pages: 24

Brand: jcm-tech Pages: 8

Brand: Kathrein Pages: 16

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands