Siemens Synco living Operating Instructions Manual Download Page 57

Page: 57 / 100

57 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Actual value of the DHW temperature

The actual value of the DHW temperature can be displayed:

Main menu > DHW > DHW state > Act val DHW temp:

DHW temperature setpoint

The current DHW temperature setpoint can be queried:

Main menu > DHW > DHW state > DHW temp setpoint:

Operating state of charging pump and electric
immersion heater

The current operating state of the charging pump and the electric immersion
heater can be displayed:

Main menu > DHW > DHW state > Charging pump:

Main menu > DHW > DHW state > El immersion heater:

Plant operation

The current operating state of DHW heating (Off / Ready / Charging) can be
displayed:

Main menu > DHW > DHW state > Plant operation:

Reason for DHW plant operation

The reason for the current DHW plant operation can be displayed (commis-
sioning / frost / legionella function / time switch):

Main menu > DHW > DHW state > Cause:

Limitation of charging time

This display shows whether limitation of the charging time is currently inactive
or active. The maximum permissible charging time was preset when the plant
was commissioned.

Main menu > DHW > DHW state > Charging time limit:

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands