Siemens Synco living Operating Instructions Manual Download Page 49

Page: 49 / 100

49 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Ventilation state

Ventilation stage

Shows the active ventilation stage (Off, Stage1, Stage2, Stage3).

Main menu > Ventilation > Ventilation state > Vent stage:

Reason

Display the reason for the current ventilation stage.

Possible reasons:

•

Commissioning

•

No request

•

Operating mode

•

Air quality

•

Ventilation contact

•

Humidity limitation

•

Night cooling

•

Stage selector

•

Window open

•

Smoke

•

Forced ventilation

Main menu > Ventilation > Ventilation state > Cause:

HR bypass

Shows if HR bypass (e.g. for night cooling) is active.

Main menu > Ventilation > Ventilation state > HR bypass:

Indoor air quality

Shows the current indoor air quality (0..2000 ppm) on the sensing element.

Main menu > Ventilation > Ventilation state > IAQ:

Air humidity

Shows the relative air humidity (0..100%) on the sensing element.

Main menu > Ventilation > Ventilation state > Air humidity:

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands