Siemens Synco living Operating Instructions Manual Download Page 47

Page: 47 / 100

47 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Stage setpoints

Stage assignment to operating modes

The individual ventilation operating modes can be assigned to the correspond-
ing ventilation stages via stage setpoints.

This setting has no influence, if ventilation is controlled by relative
humidity or air quality.

Main menu > Ventilation > Stage setpoints > Comfort:

Main menu > Ventilation > Stage setpoints > Precomfort:

Main menu > Ventilation > Stage setpoints > Economy:

Main menu > Ventilation > Stage setpoints > Protection:

Factory

setting

Setting

Comfort

Stage 1

Off

Stage 1

Stage 2

Stage 3

Precomfort

Stage 1

Off

Stage 1

Stage 2

Stage 3

Economy

Off

Stage 1

Stage 2

Stage 3

Protection

Off

Stage 1

Stage 2

Stage 3

Stage assignment to window states

Specify the stage for ventilation when the central apartment unit detects an
open window (see page 54).

Main menu > Ventilation > Stage setpoints > Window open:

Factory setting

Off

Setting

Off

Stage 1

Stage 2

Stage 3

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands