Siemens ST950 User Manual Download Page 14

Page: 14 / 178

ST950 Plus+ User Manual

Page 14 of 176

667/HE/53000/000

Issue 2

Unrestricted

LUS

NTRODUCTION AND

ASIC

RINCIPLES

The Siemens ST950 Plus

system is part of the wider ST950 family of controllers and associated

equipment. The ST950 Plus

system will run very similar firmware and offers same facilities as the

rest of the ST950 family, including license enabled integral MOVA8 and integral UTMC OTU
facilities.

The ST950 Plus

Controller is supplied as a single-door outer case with a 6U logic rack and

equipment mounting frame.

Figure 1 : Comparison of Traffic Cabling Methodologies

The Plus

Traffic Controller provides ELV Power and communications, using a four-core armoured

cable, to a number of intelligent Plus

Nodes on the street. The cable connects at the cabinet to a

‘Cabinet Interface Card’ (CIC) via its ‘Cable Termination Backplane’ (CTB).

Each CIC supports a number of on-street cables (arms or rings) each with individual electronically
controlled power switch off capabilities.

Summary of Contents for ST950



















































































































































































Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands

Siemens ST950, User Manual

Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands