Siemens SIWAREX WP321 Operating Instructions Manual Download Page 101

Page: 101 / 132

Command lists

The commands for the electronic weighing system described here can be transmitted by

several interfaces:
● From the operator panel via the controller to the SIWAREX module
● From SIWATOOL direct to the SIWAREX module
A data or command error is signaled if a command cannot be executed or if the sent data record

is rejected.

Command

code

Command

Description

Service

1... 99

Service commands

Service mode On

Turn on service mode

Service mode Off

Turn off service mode

Load factory setting

The command resets the SIWAREX to the "Ex facto‐

ry" status:

- All parameters and saved data are loaded with the

default values.

- All message buffers are reset.

Set Calibration Point 0

Set Calibration Point 0 / save values for calibration

point 0.

Set Calibration Point 1

Set Calibration Point 1 / save values for calibration

point 1.

Set Calibration Point 2

Set Calibration Point 2 / save values for calibration

point 2.

Characteristic shift

Move calibration characteristic. The command de‐

fines the current weight of the scale as the new zero

point (0 kg) and shifts the complete characteristic

without changing the gradient.

The command can be used, for example, in order to

compensate parts used for mounting calibration

weights on the scale at the end of the calibration.

Perform automatic calibration

Calculating the scale characteristic curve with refer‐

ence to the load cell from data record 10. The calcu‐

lated characteristic curve is entered directly in data

record 3 and 4, and thus activated immediately after

executing the command.

Perform calibration check

The command calculates the theoretical digital val‐

ues in relation to the calibration weights using the

load cell parameters from data record 10 and the ad‐

justment weights 0, 1 and 2 from data record 3. The

output of these theoretical digits is made in data re‐

cord 4. The function can be used to check the plau‐

sibility of adjustment digits in data record 3, which

have been determined in a legal-for-trade calibration.

700 … 899

HMI display switching

SIWAREX WP321

Operating Instructions, 08/2019, A5E33715669A-AD

101

Summary of Contents for SIWAREX WP321





































































































































Search results

Summary of Contents for SIWAREX WP321

Reviews:

Siemens SIWAREX WP321, Operating Instructions Manual, Page: 101 / 132

Search results

Summary of Contents for SIWAREX WP321

Reviews: