manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 94

Scale parameters and functions 

 

8.8 DR 7 Process interfaces 

 

SIWAREX WP251 

94

 

Manual, 12/2015, A5E37203357A 

8.8.12

 

Output value following fault or SIMATIC STOP 

With the default settings, the analog output is switched off following a module fault (operating 

error) or at a SIMATIC S7-1200 CPU STOP. 
If the analog output is, for example, to be set to 3.5 mA following a fault, this is defined using 

this parameter. The current value to be output is entered in mA. 

 

 

NOTICE 
System can be switched to unsafe state 
If the analog output is to be set to a given value following a fault (operating error), you must 

ensure that this poses no danger. 

 

8.8.13

 

Trace recording cycle 

The trace function is used for the continuous recording of measured values. The recording 

rate is defined with the parameter. 

 

Function code 

Response 

1 

Recording every 10 ms 

10 

Recording every100 ms 

100 

Recording every 1000 ms 

1000 

Recording every 10000 ms 

8.8.14

 

Trace storage method 

This parameter is used to specify the response of the trace memory. 

 

Value 

Response 

0 

Trace recording runs as circulating memory 

1 

Trace recording is stopped when memory is full and a technology message is output. 

 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands