manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 192

Communication with SIMATIC S7-1200 

 

11.1 Integration in SIMATIC S7-1200 

 

SIWAREX WP251 

192

 

Manual, 12/2015, A5E37203357A 

Parameter (read) 

Meaning 

TECHNOLOGICAL_ERR

ORS_1 

Technology error word 1 according to the "Messages" section 

TECHNOLOGICAL_ERR

ORS_2 

Technology error word 2 according to the "Messages" section 

DATA_CMD_ERRORS_1  Data/command error word 1 according to the "Messages" section 
DATA_CMD_ERRORS_2  Data/command error word 2 according to the "Messages" section 
DATA_CMD_ERROR_AD

D_INFO 

Additional information for data/command errors according to the "Messages" section 

Parameter (write) 

Meaning 

PRESET_TARE_VALUE  Preset tare value (can be used via command 1016 or with corresponding "Dosing start option" 

(DR 25) for taring) 

AQ_CONTROL 

Control value for the analog output (the output must be configured accordingly for this in DR 7) 

DQ_CONTROL 

Control bits for the four digital outputs (the outputs must be configured accordingly for this in 

DR 7) 

TRANSITIONS 

Blocking conditions for weighing steps 0-7. For example, if the "TRANSITION_STEP_2" bit is 

set and a weighing is started, WP251 stops the weighing cycle after performing weighing step 

1 and sets the "Step blocked (transition)" bit in the AWI Status. The weighing or weighing step 

2 is not continued until the "TRANSITION_STEP_2" bit is reset. 

SECURE_DISPLAY_CON

TROL 

Parameter for communication of the calibratable "SecureDisplay" display with the SIWAREX 

WP251 module. The "SecureDisplay" communication block is interconnected with this pa-

rameter for scales requiring official calibration. 

11.1.6

 

Error codes of function block 

 

Table 11- 2  Statuses/errors when working with the function block 

Error bit 

Error description 

bo_ApplIDError 

Address module does not match the function block 

bo_ApplIDDRError 

Data record does not match the inserted module 

bo_SFBError 

Runtime error during transmission of data record 

bo_RdPerError 

Reading of I/O data failed 

bo_LifeBitError 

SIWAREX no longer responds 

bo_StartUpError 

Command was sent although StartUp is still TRUE 

bo_WrongFW 

Data record version does not match the firmware 

bo_InvalidCMD 

An invalid command code was sent 

bo_DataOperationError 

Synchronous data operation error has occurred 

bo_StartUp 

Startup synchronization of module running 

 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands