manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 189

 

Communication with SIMATIC S7-1200 

 

11.1 Integration in SIMATIC S7-1200 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

189

 

11.1.4

 

Working with the function block 

Data records in SIWAREX weighing modules 

All parameters in SIWAREX weighing modules are structured in data records. These data 

records must be considered as connected packages and can only be respectively read into 

the CPU or written to the SIWAREX as complete packages. Reading or writing of a single 

parameter within a data record is not possible. You can find a description of all data records 

and their parameters in chapter → 

Scale parameters and functions (Page 57). 

Reading and writing of data records is carried out using special command codes which can 

be sent with three command mailboxes handled according to priority within the instance DB: 

 

Image 11-6  CMD command mailboxes  

As shown in the graphics, a command mailbox always consists of a command code (Int) and 

four bits (Bool). A command is set by entering the desired command code in the 

"i_CMD_CODE" parameter and setting the respective command trigger 

"bo_CMD_TRIGGER". The status bits "bo_CMD_InProgress" (command being processed), 

"bo_CMD_FinishedOk" (command finished without errors) and "bo_CMD_FinishedError" 

(command rejected or finished with error) can be evaluated in the user program. 
In addition, the three command mailboxes are managed and processed according to priority. 

CMD1 has the highest priority, CMD3 has the lowest priority. If all three command mailboxes 

are triggered simultaneously by the user program, for example, the function block initially 

processes CMD1, then CMD2, and finally CMD3. Cyclic triggering of command mailbox 3 is 

also interrupted by intermediate sending of a command in mailbox 2 or 1 for processing of 

the respective command. 

 

 

Note 
Cyclic triggering of the CMD1 command mailbox makes it impossible to send commands in 

mailbox 2 or 3. 

 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands