manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 165

Errors and messages 

9.6 Operating errors 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

165

 

Operating errors 

Error 

code 

Description and remedy 

1004 Checksum error 

1004 

The checksum of the WP251 FW no longer matches. Remedy: Load factory 

settings. Contact SIWAREX Support if the error recurs. 

Reserve 

Reserve  Reserve 

1006 Logbook error 

1006 

Error when writing/clearing the logbook. Remedy: Load factory settings. 

Contact SIWAREX Support if the error recurs. 

1007 Application error 

1007 

Incompatible FW was loaded. Remedy: Load only WP251-compatible FW 

on the module. 

1102 ADC error 

1102 

AD converter error when reading in the measured value. Remedy: Check 

and follow recommendations for installation meeting EMC requirements 

(section EMC-compliant installation (Page 25)). 

Reserve 

Reserve  Reserve 

1104 Undervoltage at SENSE 

1104 

Undervoltage on the SENSE cables. A voltage between 4.85 V DC and 

X.XX V DC must be present between SEN+ and SEN-. If necessary, check 

the wiring of the load cells or, in the case of 4-wire load cells, the jumpers 

between EXC+&SEN+ and EXC-&SEN- in the junction box. 

1105 Overload at SIG 

1105 

The maximum SIG input signal of the AD converter is exceeded by more 

than 10% (corresponds to +21.34 mV). Check the wiring of the load cell(s). 

If wiring is correct, check the input and output resistance of the cells and 

identify any defective cells. 

1106 Underload at SIG 

1106 

The minimum SIG input signal of the AD converter is fallen below by more 

than 10% (corresponds to -21.34 mV). Check the wiring of the load cell(s). If 

wiring is correct, check the input and output resistance of the cells and iden-

tify any defective cells. 

1107 Communication with Se-

cureDisplay failed 

1107 

The calibratable "SecureDisplay" weight display no longer communicates 

with WP251. Check the cabling between the HMI and CPU or SIWAREX, 

the SIMATIC S7 program and the IP addresses of the networked compo-

nents. 

Reserve 

Reserve  Reserve 

Reserve 

Reserve  Reserve 

9.6.2

 

Technology messages 

Table 9- 1 

Technology messages 

Technology errors 

Error code  Description and remedy 

2000 Technological error 

2000 

Group message, at least one technology message is 

present 

2001 Timeout tare or zero set-

ting 

2001 

Taring or zero setting is not possible because a stand-

still was not reached during the standstill waiting time 

Check the standstill criteria and the standstill waiting 

time in DR 3 and adjust the parameters as necessary. 

Check the scale mechanics for strong fluctuations / 

disturbances that prevent standstill. 

2002 Trace error 

2002 

The set recording rate for trace function cannot be 

processed. Set a slower recording rate (section "Trace 

recording cycle (page 91)") 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands