manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 145

Scale parameters and functions 

8.29 DR 32 Error messages 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

145

 

8.28.11

 

Current load cell signal in mV 

Display of currently measured signal voltage of the load cell(s) between the SIG+ and SIG- 

terminals in millivolts (mV). 

8.28.12

 

Current fine weight 

This parameter indicates the calculated fine weight currently used by WP251. The value can 

differ from the specification in DR 23 because it may have been adjusted by the proportional 

controller. 

8.28.13

 

Current trailing weight 

This parameter indicates the calculated trailing weight currently used by WP251. The value 

can differ from the specification in DR 23 because it may have been adjusted by the 

proportional controller. 

8.28.14

 

Tolerance limits TH2, TH1, TL1 and TL2 

The tolerance limits specified in DR 22 are always output in DR 31 in the weight unit 

because different options are available in DR 22 for specifying the tolerance limits (absolute 

values, relative values or according to OIML R-61). 

8.29

 

DR 32 Error messages 

8.29.1

 

Overview 

Data record DR 32 is used for Modbus communication with a Modbus master in order to 

identify or evaluate an error message from WP251. The individual message bits are set to 

TRUE state for three seconds in the event of an error and do not have to be acknowledged 

to the SIWAREX module. 
All Modbus registers in DR 32 are automatically updated and do not have to be requested by 

a read command. 
For operation with a SIMATIC CPU, the use of DR 32 is unnecessary because the error 

information is made available to the CPU or HMI automatically in the data block via the I/O 

area of the WP251. 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands