manualshive.com logo in svg

Siemens SIWAREX WL280, Operating Instructions Manual, Page: 36 / 58

Share
Download
Siemens SIWAREX WL280 Operating Instructions Manual Download Page 36

Mounting 

 

5.2 Installing the compact installation unit 

 

RN-S SA 

36

 

Operating Instructions, 09/2016, A5E32605810A-03 

●

 

The compact installation units act as dummies. 

●

 

The compact installation units provide protection during transport. 

In this state, simple installation and transport work can be carried out compared to the rated 

load. 

5.2.6

 

Lowering the top plate onto the load cells 

 

Figure 5-8 

Lowering the top plate  

1.

 

Loosen the top nuts 

③

 in several cycles and slowly lower the load bearing implement. 

 

 

 

NOTICE 
Loosening the hexagon nuts 
Only loosen the hexagon nuts in turn in very small steps. During the process, note which 

hexagon nut is loaded and which is not. 
Note: 

•

 

The compact installation units are screwed tight to the brackets. 

•

 

By loosening a hexagon nut, the weight of the bearing implement is distributed 

among the other hexagon nuts and is partially increased. 

Avoid overloading individual hexagon nuts. 

 

2.

 

Rotate the top nuts 

③

 downward. The top plate 

①

 is lying on the load cell 

②

 via the 

pendulum supports. The respective load cell is loaded. 

3.

 

Tighten the nuts 

③

 against the bottom nuts 

④

. In this way, you prevent the nuts 

③

 from 

rotating upwards due to vibrations. 

Summary of Contents for SIWAREX WL280



























































Reviews:

No comments