manualshive.com logo in svg

Siemens SIWAREX WL280, Operating Instructions Manual, Page: 12 / 58

Share
Download
Siemens SIWAREX WL280 Operating Instructions Manual Download Page 12

Description 

 

3.1 Application 

 

RN-S SA 

12

 

Operating Instructions, 09/2016, A5E32605810A-03 

●

 

Designed relief of the load cell during installation 

●

 

Overload protection of the load cell during installation 

●

 

Prepared for the attachment of guide elements: single-sided or double-sided 

●

 

Compensation of tolerance of connection holes through mounting with spring washers 

●

 

Checking of correct installation using conical washer 

●

 

Highly flexible ground wire for protection of load cell against parasitic currents 

●

 

Parts made of stainless steel for applications in the food and pharmaceutical industries 

Compact installation unit for SIWAREX WL280 RN-S SA 

The type SIWAREX WL280 RN-S SA self-centering compact installation unit for load cells is 

especially well suited for installation in container scales, platform scales and roller table 

scales. 

 

3.1.2

 

Lifting protection 

The lifting protection prevents the load bearing implements from being lifted off the load 

cells.  
If there is a risk of the load bearing implement being lifted or toppled, then lifting protection is 

required. This is required in the case of lightweight containers and tall, outdoor silos. 

3.1.3

 

Overload protection 

The overload protection protects load cells from a load that is too great.  
There is overload protection against excessive loads in the measuring direction and overload 

protection against excessive transverse forces. 
Transverse forces are caused by, for example, wind, filling processes, acceleration, or 

conveyor belt friction. If these forces exceed certain values, the load cells must be protected 

from them. 

Summary of Contents for SIWAREX WL280



























































Reviews:

No comments