Siemens Siwarex U Device Manual Download

Page: 77 / 89

11BORDER NUMBERS AND ACCESSORIES

12 Order numbers and accessories

There are essential and optional accessories for SIWAREX U.

The essential accessories are indicated in the following table.

Order no.

SIWAREX U

for SIMATIC S7 and ET 200M, incl. bus connectors, weight 0.3 kg

•

One-channel design

1) A)

for the connection of one scale

7MH4950-1AA01

•

Two-channel design

2) A)

for the connection of two scales

7MH4950-2AA01

SIWAREX U device manual

•

In various languages

Free download on the Internet at:

www.siemens.de/waegetechnik

Configuration package

SIWAREX U for SIMATIC S7 and TIA-Portal

on CD-ROM

•

PC software SIWATOOL U (various languages), new design

•

Sample program "Getting started" – ready-made application for

SIMATIC S7

•

Device manual SIWAREX U on CD (various languages)

•

Quick Guide

•

HSP Hardware Support Package for incorporation of SIWAREX U

in STEP 7 classic

7MH4950-1AK02

Configuration package SIWAREX U for PCS 7, Version 7.x

in German and English on CD-ROM, block for CFC plan and face-plate
(image block)

7MH4950-3AK61

SIWATOOL connection cable

from SIWAREX U/CS with serial PC port, for 9-pin PC ports (RS 232),
length 3 m

7MH4607-8CA

Installation material (absolutely necessary)

Front connector 20-pin with screw contacts

(required for each SIWAREX module)

6ES7392-1AJ00-0AA0

Shield connection element

sufficient for two SIWAREX U modules

6ES7390-5AA00-0AA0

SIWAREX U

12-69

Summary of Contents for Siwarex U


























































































Search results

Summary of Contents for Siwarex U

Reviews:

Related manuals for Siwarex U

Brands by name

Popular brands

Siemens Siwarex U, Device Manual

Search results

Summary of Contents for Siwarex U

Reviews:

Related manuals for Siwarex U

Brands by name

Popular brands