manualshive.com logo in svg

Siemens SIWAREX FTC, Device Manual

Share
Download
Siemens SIWAREX FTC Device Manual Download Page 66

 

5.5.12  DR 5 – Minimum flow-rate 

Minimum flow-rate is a limit value for minimum flow-rates in % of the 

nominal flow-rate. The entry of the number e.g. 800 corresponds with 80.0 

%. After this value has been undercut, SIWAREX FTC sets a status bit. 

5.5.13  DR 5 – Maximum flow-rate 

Maximum flow-rate is a limit value for maximum flow-rates in % of the 

nominal flow-rate. The entry of the number e.g. 1020 corresponds with 

102.0 %. After this value has been exceeded, SIWAREX FTC sets a status 

bit. 

5.5.14  DR 5 – Minimum belt loading 

Minimum belt loading is a limit value for minimum belt loading in % of the 

nominal belt loading. The entry of the number e.g. 800 corresponds with 

80.0 %. After this value has been undercut, SIWAREX FTC sets a status 

bit. In batch mode the totalizing will be completed after the dosing signal is 

switched off and the belt loadin is less than this limit value. 

5.5.15  DR 5 – Maximum belt loading 

Maximum belt loading is a limit value for maximum belt loading in % of the 

nominal belt loading. The entry of the number e.g. 1020 corresponds with 

102.0 %. After this value has been exceeded, SIWAREX FTC sets a status 

bit. 

5.5.16  DR 5 – Maximum belt loading for zero setting 

Maximum belt loading for zero setting is a limit value for maximum belt 

loading in % of the nominal belt loading. Entering the number e.g. 20 

corresponds with 2.0 %. After this value has been exceeded, SIWAREX 

FTC will not execute the zero setting instruction. 

5.5.17  DR 5 - Minimum belt loading for totalizing 

Minimum belt loading for totalizing is a limit value for minimum belt loading 

in % of the nominal belt loading. Entering the number e.g. 20 corresponds 

with 2.0 %. After the actual value is less than the limit, SIWAREX FTC will 

not execute the totalizing function. 
 

5.5.18  DR 5 – Delay time for the monitoring of the belt  loading after the start 

After the belt is switched on, undercutting the minimum belt loading or the 

minimum flow-rate is only indicated after this time has elapsed. 

5.5.19  DR 5 – Delay time for monitoring the belt loading in continuous operation 

After the minimum belt load has been undercut or the minimum flow-rate is 

undercut, the respective message or status bit is output only after this time 

has elapsed. 

5-54

 

SIWAREX FTC

 

Summary of Contents for SIWAREX FTC






















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands