manualshive.com logo in svg

Siemens SIWAREX FTC, Device Manual

Share
Download
Siemens SIWAREX FTC Device Manual Download Page 21

P

RODUCT 

O

VERVIEW

 

SIWATOOL FTC_B can also be used for reading the contents of the records from 
the calibratable scale memory. 

The following figure shows the structure of the individual program windows. 

Figure 3-2 

SIWATOOL FTC_B Overview 

 

SIWATOOL FTC_B does not only support the user in entering parameters. It is 
very useful to analyze the diagnostic buffer, the contents of which can be saved 
along with the parameters after reading from the module. 

A trace mode exists in the SIWAREX FTC module for optimizing weighing 
progress. The recorded data can be displayed in a curve diagram using MS Excel. 
These records can then be used to e.g. analyze and optimize the material flow for 
a shift. 

3.8  Firmware Download with SIWATOOL FTC_B 

Another feature of the SIWATOOL FTC_B program helps in loading a new version 
of firmware onto the SIWAREX FTC, on-site. It allows upgrades or function 
expansions for the firmware at any time and from anywhere.  

3.9  Reading the Stored Weighing Logs with SIWATOOL FTC_B  

The weighing logs are stored on an MMC (Micro Memory Card) that can be 
inserted into the SIWAREX FTC. If a person disagrees with the results of a certain 
weighing procedure, the weighing data for that weighing procedure can be 
reconstructed from the MMC memory. 

SIWAREX FTC 

3-9 

Summary of Contents for SIWAREX FTC






















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands