manualshive.com logo in svg

Siemens SITRANS WW100, Operating Instructions Manual

Share
Download
Siemens SITRANS WW100 Operating Instructions Manual Download Page 28

Your system has been supplied with soft PVC seal strips. Position the seal strips on the belt as 

shown. 

1

2

3

4

5

①

Pulley

④

Do not force seal strip against belt

②

Seal strip

⑤

Belt

③

Skirtboard

 

 

Note
Skirtboard seal stripping is not FDA or USDA approved material, and should be removed for 

critical food applications.

7.3

Changing the conveyer belt

WARNING

ALWAYS STOP the belt, lock-out, and/or place a "Do Not Energize" tag on the main 

disconnect before working on or around the weighfeeder.

Depending on the size of the weighfeeder, several personnel may be required to remove and 

re-install the belt.
1. On enclosed models, open and remove the access and non-access side panels.
2. Mark the current position of the telescoper for reference. This will be a reference when you 

re-install the belt. Loosen the telescopers to remove tension from the belt.

3. Rotate the belt tension roller up against the back of the infeed and support it during belt 

change. This tensioner may need to be removed for ease of belt change. It is located at the 

infeed end of the weighfeeder.

4. To make the belt change easier, remove the belt scraper counterweight located at the 

discharge end of the conveyor.

5. Move the belt out from the side guide roller.

Commissioning
7.3 Changing the conveyer belt

SITRANS WW100

28

Operating Instructions, 06/2018, A5E33560618-AC

Summary of Contents for SITRANS WW100















































Reviews:

No comments

Brands by name

Popular brands

Load more brands