Siemens SITRANS T4200 Operating Instructions Manual Download

Page: 68 / 100

Functions

9.21 Individual password protection (only in SITRANS TH300)

SITRANS TH200/TH300
Operating Instructions, 06/2010, A5E00393069-03

9.21

Individual password protection (only in SITRANS TH300)

Description

The individual password protection prevents unauthorized write access to the device.

Note
Password protection



Change the default password immediately after commissioning the device. You will then

prevent write access to the device by unauthorized persons.



Store your new password in a secure location.



Consult the Siemens contact person in your region to receive your "super pin".



When you activate the password protection in the device, write protection will be set

automatically after the device has been switched on.

In the condition of goods delivered, every transmitter is set with the default password 2457.

Password protection is deactivated. If you reset the transmitter to the factory setting, the

current password will not be reset to the default password. Should you no longer know your

password, then the data in the device can only be altered using a "super pin", therefore not

using the default password. The super pin can be obtained from your regional Siemens

contact person.

Procedure for writing data in a password protected device

Select the "Deactivate password protection" menu in the parameterization software.

Enter your 4-digit password. Password protection is deactivated.

Change the values according to your application.

Select the "Activate password protection" menu in the parameterization software. The

device is write protected again.

Summary of Contents for SITRANS T4200





































































































Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands

Siemens SITRANS T4200, Operating Instructions Manual

Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands