Siemens SITRANS T4200 Operating Instructions Manual Download

Page: 25 / 100

Connecting

5.1 Safety notes on the connection

SITRANS TH200/TH300

Operating Instructions, 06/2010, A5E00393069-03

5.1.2

Safety notes when connecting in hazardous areas

WARNING

Observe the degree of protection
The device must be connected to the supply and signal circuits named in the certificate or

on the nameplate.
When installing the device in hazardous areas:
Use enclosures/connection heads with the degree of protection corresponding to the test

certificate applicable in your country.

WARNING

Electrical connection in hazardous areas
The national directives and laws for hazardous areas valid in your country must be

observed for electrical connection. In Germany these are, for example:



The health and safety at work regulations



The directive for "Installation of electrical systems in hazardous areas", DIN EN 60079-

14 (previously VDE 0165, T1)



The EC type examination certificate

When an auxiliary power supply is needed, check whether the auxiliary power supply

matches that given on the nameplate and the inspection certificate valid in your country.

CAUTION

Limited range of use
If the device has been operated outside the ambient conditions specified for potentially

explosive atmospheres, you may no longer operate the device in potentially explosive

atmospheres. Make sure to permanently mask all Ex markings on the nameplate.

NOTICE

Loss of type of protection "Intrinsic safety"
If the transmitter is not operated with an intrinsically-safe power supply, the type of

protection "Intrinsic safety" is no longer guaranteed and the intrinsically-safe approval may

be revoked.
Permanently erase, therefore, the irrelevant types of protection on the nameplate before

commissioning to ensure that erroneous deployment is avoided.

The 4 to 20 mA input and sensor circuits are electrically isolated and have been tested with a

voltage of 1.5 kV DC/1 minute.
The sensor circuit is reliably galvanically isolated from the auxiliary power supply and signal

circuit, up to a peak value of the rated voltage of 60 V. Be sure to observe the construction

directives valid at the construction location for electrical resources in hazardous areas. In

Europe, this is the standard EN 60079-14.

Summary of Contents for SITRANS T4200





































































































Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands

Siemens SITRANS T4200, Operating Instructions Manual

Search results

Summary of Contents for SITRANS T4200

Reviews:

Related manuals for SITRANS T4200

Brands by name

Popular brands