manualshive.com logo in svg

Siemens SITRANS L Series, Operating Instructions Manual, Page: 89 / 106

Share
Download
Siemens SITRANS L Series Operating Instructions Manual Download Page 89

Diagnostics and troubleshooting
12.5 Treatment of measurement errors

Code
Text message

Cause

Rectification

DevSpec
State in CMD 48

M510
No

communication

with the main

controller

Communication between main

electronics and display module

disturbed

Check the connection cable to

the display
Send transmitter for repair

Bit 10 of

Byte 14 … 24

M511
Inconsistent

software

configuration

A software unit requires a

software update

Carry out software update

Bit 11 of

Byte 14 … 24

12.5

Treatment of measurement errors

The tables below give typical examples of application-related measurement errors.
The images in column " 

Error description

"

 show the actual level as a dashed line 

and

 

the output level as a solid line.

  1  

Real level

  2  

Level displayed by the transmitter

Note

If the output level is constant, the cause could also be the fault setting of the current

 

output to " 

Hold value

"

.

If the level is too low, the reason could be a line resistance that is too high

Fault description

Cause

Rectification

Min./max. adjustment not correct

Adapt min./max. adjustment

Measured value shows a

too low or too high level

Incorrect linearization curve

Adapt linearization curve

Measured value jumps

towards 100 %

Due to the process, the amplitude

of the level echo sinks
A auto false echo suppression was

not carried out

Carry out a auto false echo

suppression

80

SITRANS LR150

Operating Instructions, 08/2020, 

A5E50352155

Summary of Contents for SITRANS L Series











































































































Reviews:

No comments