manualshive.com logo in svg

Siemens SITRANS L Series, Operating Instructions Manual, Page: 70 / 106

Share
Download
Siemens SITRANS L Series Operating Instructions Manual Download Page 70

Setup with the integrated HMI

7.9 Communication

7.9

Communication

7.9.1

HART address

Function

POLLING ADR:

Sets the device address in a HART network.
For point-to-point configurations the standard address is zero (0).
For multidrop configurations, use a non-zero HART address, i.e. 1 to 63.

7.10

Safety

7.10.1

user PIN

Is used to activate/deactivate the user PIN. If the user PIN is activated, a PIN must be

entered when changing parameter settings.

Note

The device is unlocked on delivery.
A  change  of  the  setting  for  parameter  " 

User  PIN

"

  does  not  take  effect 

immediately.

 

After changing the setting, the device must be restarted or ten (10) 

minutes must

 

elapse before the change takes effect.

Setting

Selection

Selection

Description

ACTIVT

Activate User PIN
Display = OK

USER PIN

USER PIN

CANCL

Deactivate User PIN
Display = ENABL

7.10.2

Bluetooth PIN

BLUETOOTH PIN:

In this menu item, you can change the factory-preset Bluetooth access code to your

personal Bluetooth access code.

Note

The individual preset Bluetooth access code of the device can be found on the

 

supplied information sheet " 

Device Bluetooth and Parameter Access Codes

"

. If this

SITRANS LR150

Operating Instructions, 08/2020, 

A5E50352155

61

Summary of Contents for SITRANS L Series











































































































Reviews:

No comments