Siemens SITRANS L Series Operating Instructions Manual Download Page 69

Page: 69 / 106

Setup with the integrated HMI
7.8.5 Frequency

Setting

Selection

Description

Cancel

DIST

Distance

RESET

RESET PEAK

STEMP

Electronics temperature

7.8.5

Frequency

Country specific settings for the radar signals are determined via the menu item

frequency.

• Frequency 1: EU, Albania, Andorra, Azerbaijan, Australia, Belarus, Bosnia and

Herzegovina, Canada, Liechtenstein, Moldavia, Monaco, Montenegro, New

Zealand, Northern Macedonia, Norway, San Marino, Saudi Arabia, Serbia,

Switzerland, Turkey, Ukraine, United Kingdom, USA

• Frequency 2: South Korea, Taiwan, Thailand
• Frequency 3: South Africa
• Frequency 4: Russia
Depending on the frequency, the metrological properties of the device can change

(see chapter "

Technical data, input variable

Further information can be found in the document "

Regulations for radar level

measuring transmitters with radio licenses

on our homepage.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Summary of Contents for SITRANS L Series











































































































Search results

Summary of Contents for SITRANS L Series

Reviews:

Siemens SITRANS L Series, Operating Instructions Manual, Page: 69 / 106

Search results

Summary of Contents for SITRANS L Series

Reviews: