Siemens SITRANS L Series Operating Instructions Manual Download Page 53

Page: 53 / 106

Setup with the integrated HMI
7.5.5 Quick setup auto false echo suppression

Scaling format

SCALE FORMAT:

Sets the decimal places with which the process value is displayed.

Final scaling value

UPPER SCALNG:

Sets the process value that corresponds to a loop current of 20 mA.

Confirm

CONFIRM:

Accepts the settings as the last step in the wizard.

Setting Yes:

The wizard is closed and settings are applied.

Setting No:

The wizard is closed and settings are not applied. They must be entered again when

the wizard is run again.

7.5.5

Quick setup auto false echo suppression

Use

Used to prevent the detection of false echoes in a specified range.

Use the AFES wizard if there are known installations in the application and if false

echoes are to be expected.

Notes

If possible, set the automatic false echo suppression (AFES) during commissioning by

executing the "

Auto false echo suppression wizard

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Summary of Contents for SITRANS L Series











































































































Search results

Summary of Contents for SITRANS L Series

Reviews:

Siemens SITRANS L Series, Operating Instructions Manual, Page: 53 / 106

Search results

Summary of Contents for SITRANS L Series

Reviews: