manualshive.com logo in svg

Siemens SITRANS L Series, Operating Instructions Manual, Page: 32 / 106

Share
Download
Siemens SITRANS L Series Operating Instructions Manual Download Page 32

Access protection

6

6.1

Bluetooth radio interface

Bluetooth PIN

Bluetooth PUK

Devices with a Bluetooth radio interface are protected against unwanted access from

 

outside. This means that only authorized persons can receive measured and status

 

values and change device settings via this interface.

A Bluetooth PIN is required to establish Bluetooth communication via the adjustment

 

tool (smartphone/tablet/notebook). This code must be entered once when Bluetooth

 

communication is established for the first time in the adjustment tool. It is then

 

stored 

in the adjustment tool and does not have to be entered again.
The Bluetooth PIN is individual for each device. It is supplied with the device in the

 

information sheet " 

Device Bluetooth and Parameter Access Codes

"

. It can be changed

 

by the user after the first connection has been established. If the Bluetooth PIN has

 

not 

been entered correctly, a new entry can only be made after a waiting period has

 

elapsed. The waiting time increases with each additional incorrect entry.

The Bluetooth PUK enables Bluetooth communication to be established in the event

 

that the Bluetooth PIN is no longer known. It can't be changed. The Bluetooth PUK

 

can 

be found in information sheet " 

Device Bluetooth and Parameter Access Codes

"

. If

 

this 

document is lost, the Bluetooth PUK can be retrieved from your personal contact

 

person 

after legitimation. The storage and transmission of Bluetooth access codes is

 

always 

encrypted (SHA 256 algorithm).

6.2

Protection of the parameterization

The settings (parameters) of the device can be protected against unwanted changes.

The parameter protection is deactivated on delivery, all settings can be made.

user PIN

To protect the parameterization, the device can be locked by the user with the aid of

a freely selectable user PIN. The settings (parameters) can then only be read out, but

not changed. The user PIN is also stored in the adjustment tool. However, unlike the

Bluetooth PIN, it must be re-entered for each unlock. When using the adjustment app

or EDD, the stored user PIN is then suggested to the user for unlocking.

SITRANS LR150

Operating Instructions, 08/2020, 

A5E50352155

23

Summary of Contents for SITRANS L Series











































































































Reviews:

No comments