manualshive.com logo in svg

Siemens SITRANS L Series, Operating Instructions Manual, Page: 17 / 106

Share
Download
Siemens SITRANS L Series Operating Instructions Manual Download Page 17

Description
3.2 Principle of operation

Constituent parts

  1  

Ventilation/pressure compensation

  2  

Display and adjustment unit

  3  

Electronics housing

  4  

Radar antenna

  5  

Process fitting

  6  

Process seal

Figure 3.1

Components of SITRANS LR150 (Example process fitting G1½)

Nameplate

The nameplate contains the most important data for identification and use of the

transmitter.

  1  

Transmitter type

  2  

Serial number

  3  

Technical data

  4  

Field for approvals

  5  

QR code for device documentation

  6  

Wireless access via smart device

Figure 3.2

Layout of the nameplate (example)

3.2

Principle of operation

Application area

SITRANS LR150 is a radar transmitter for non-contact, continuous level

measurement. It is suitable for liquids and solids in practically all industries.

8

SITRANS LR150

Operating Instructions, 08/2020, 

A5E50352155

Summary of Contents for SITRANS L Series











































































































Reviews:

No comments