manualshive.com logo in svg

Siemens SITRANS L Series, Operating Instructions Manual, Page: 16 / 106

Share
Download
Siemens SITRANS L Series Operating Instructions Manual Download Page 16

Description

3

3.1

Configuration

Scope of delivery

The scope of delivery encompasses:
• SITRANS LR150 radar transmitter
• Information sheet " 

Documents and software

"

 with:

• Transmitter serial number
• QR code with link for direct scanning

• Information sheet " 

Device Bluetooth and Parameter Access Codes

"

 with:

• Bluetooth PIN
• Bluetooth PUK
• Device Access PUK 

The further scope of delivery encompasses:
• Documentation

• Ex-specific " 

Safety instructions

"

 (with Ex versions)

• If necessary, further certificates 

Note

Optional transmitter features are also described in this operating instructions

manual. The respective scope of delivery results from the order specification.

Scope of this operating instructions

This operating instructions manual applies to the following transmitter versions:
• Hardware version from 1.0.0
• Software version from 1.2.0

SITRANS LR150

Operating Instructions, 08/2020, 

A5E50352155

7

Summary of Contents for SITRANS L Series











































































































Reviews:

No comments