Siemens SITRANS L LU240 Compact Operating Instructions Download

Page: 55 / 60

HART communication

This device supports HART

communication protocol.

SITRANS Probe LU240 can be configured over the HART network using the HART

Communicator 375/475 by Emerson, or a software package. The recommended software

package is the SIMATIC Process Device Manager (PDM) by Siemens.

Note
Supported HART parameters
For a list of applicable parameters, see the full operating instructions.

SIMATIC PDM
This software package is designed to permit easy configuration, monitoring, and

troubleshooting of HART devices. The HART EDD for SITRANS Probe LU240 was written with

SIMATIC PDM in mind and has been extensively tested with this software.

HART Electronic Device Description (EDD)
In order to configure a HART device, the configuration software requires the HART Electronic

Device Description specific to the device. Download the HART EDD for SITRANS Probe LU240

from the product page of our website:
● Product page (

www.siemens.com/sitransprobelu240

)

Click Support > Software Downloads. Older versions of the library will have to be updated in

order to use all the features of SITRANS Probe LU240.

SITRANS Probe LU240 with mA/HART

Compact Operating Instructions, 10/2018, A5E42673704-AB

Summary of Contents for SITRANS L LU240





























































Search results

Summary of Contents for SITRANS L LU240

Reviews:

Related manuals for SITRANS L LU240

Brands by name

Popular brands

Siemens SITRANS L LU240, Compact Operating Instructions

Search results

Summary of Contents for SITRANS L LU240

Reviews:

Related manuals for SITRANS L LU240

Brands by name

Popular brands