Siemens SITRANS L LU240 Page 30 Compact Operating Instructions Download

Page: 30 / 60

7.2.2

Local display

①

Title line

⑥

EDIT indicator

②

Main line

⑦

INFO indicator

③

UP/DOWN navigation arrows

⑧

NE107 diagnostic states

④

Info field

⑨

Bar graph

⑤

Lock symbol

⑩

Sign of the process value

7.2.3

Display symbols

INFO field

Symbol

Meaning

Device is write-protected via parameter "User PIN".

Device is write-protected via parameter "Button lock".

Loop test is running.

EDIT

When symbol is flashing, you can edit the parameter.

INFO

Diagnostic message. The ID next to the "INFO" symbol is used for

identification of the diagnostic message.

For a complete list of diagnostic messages that appear on the local display, refer to the

Diagnosing and troubleshooting chapter of the full operating instructions.

7.2.4

Display views

Note
Display views
● Edit view and measurement view refer to the display only. While the device is in edit view,

the output remains active and continues to respond to changes in the device.

● The display will return to measurement view after ten minutes of inactivity (from last button

press), when in edit view and from within a wizard. Pressing button will then take you

to the main navigation menu. (It will not return to the screen from which the timeout

occurred.)

Commissioning
7.2 Local commissioning

SITRANS Probe LU240 with mA/HART

Compact Operating Instructions, 10/2018, A5E42673704-AB

Summary of Contents for SITRANS L LU240





























































Search results

Summary of Contents for SITRANS L LU240

Reviews:

Related manuals for SITRANS L LU240

Brands by name

Popular brands

Siemens SITRANS L LU240, Compact Operating Instructions

Search results

Summary of Contents for SITRANS L LU240

Reviews:

Related manuals for SITRANS L LU240

Brands by name

Popular brands