Siemens SITRANS FC310 Compact Operating Instructions Download Page 19 | Manualshive

Page: 19 / 54

Siemens SITRANS FC310 Compact Operating Instructions Download Page 19

Installing/mounting

3

3.1

Basic safety notes

WARNING

Wetted parts unsuitable for the process media
Risk of injury or damage to device.
Hot, toxic and corrosive media could be released if the wetted parts are unsuitable for the

process medium.
● Ensure that the material of the device parts wetted by the process medium is suitable for

the medium. Refer to the information in Technical data (Page 47).

Note
Material compatibility
Siemens can provide you with support concerning selection of sensor components wetted by

process media. However, you are responsible for the selection of components. Siemens

accepts no liability for faults or failures resulting from incompatible materials.

WARNING

Unsuitable connecting parts
Risk of injury or poisoning.
In case of improper mounting, hot, toxic, and corrosive process media could be released at the

connections.
● Ensure that connecting parts (such as flange gaskets and bolts) are suitable for connection

and process media.

See also

Technical data (Page 47)

SITRANS FC310

Compact Operating Instructions, 01/2019, A5E44932112-AB

19

«
...
17
18
19
20
21
...
»

Summary of Contents for SITRANS FC310























































Reviews:

No comments