manualshive.com logo in svg

Siemens SITRANS F US SONOKIT, Operating Instructions Manual, Page: 35 / 95

Share
Download
Siemens SITRANS F US SONOKIT Operating Instructions Manual Download Page 35

 

Commissioning 

 

6.4 Commissioning via PDM 

SITRANS FUS080 transmitter 
Operating Instructions, 07/2012, A5E03059912-02 

33

 

The commissioning is divided into the following steps: 
1.

 

Installing and connecting in the IrdA interface adapter 

2.

 

Installing the device driver (Page 34) 

3.

 

Adding the device to the network (Page 34) 

4.

 

Configuring the device (Page 34) 

5.

 

Optimizing the system (Page 40) 

6.

 

Checking the operation readiness (Page 41) 

6.4.1

 

Installing and connecting the IrDA interface adapter 

 

Note 

 

IrDA driver installation 
For installation of the IrDA driver, refer to the instructions delivered with the adapter. 

 

1.

 

Connect IrDA adapter to PC 

 

 

2.

 

Mount adapter on FUS080 

When the IrDA adapter is connected correctly, a small icon appears on the taskbar of your 

PC. When the mouse is placed on this icon, the device information will be shown (e.g. 

"FUS080 SN1033 is in range"). 

 

Summary of Contents for SITRANS F US SONOKIT
































































































Reviews:

No comments