manualshive.com logo in svg

Siemens SITRANS F US SONOKIT, Operating Instructions Manual, Page: 13 / 95

Share
Download
Siemens SITRANS F US SONOKIT Operating Instructions Manual Download Page 13

 

SITRANS FUS080 transmitter 
Operating Instructions, 07/2012, A5E03059912-02 

11

 

Safety notes 

2

 

 

CAUTION 

 

Correct, reliable operation of the product requires proper transport, storage, positioning and 

assembly as well as careful operation and maintenance. Only qualified personnel should 

install or operate this instrument.   

 

 

Note 
Alterations to the product, including opening or improper modifications of the product, are not 

permitted. 
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.

 

2.1

 

Laws and directives 

General requirements    

Installation of the equipment must comply with national regulations. For example EN 60079-

14 for the European Community. 

Instrument safety standards   

The device has been tested at the factory, based on the safety requirements. In order to 

maintain this condition over the expected life of the device, the requirements described in 

these Operating Instructions must be observed. 

 

NOTICE 

 

Material compatibility   
Siemens Flow Instruments can provide assistance with the selection of wetted sensor 

parts. However, the full responsibility for the selection rests with the customer and Siemens 

Flow Instruments can take no responsibility for any failure due to material incompatibility. 

 

Summary of Contents for SITRANS F US SONOKIT
































































































Reviews:

No comments