Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 78 | Manualshive

Page: 78 / 126

Siemens SITRANS F TRANSMAG 2 Operating Instructions Manual Download Page 78

Required forms

• Delivery note

• Return goods delivery note (

https://www.siemens.com/processinstrumentation/

returngoodsnote

with the following information:

– Product (item description)

– Number of returned devices/replacement parts

– Reason for returning the item(s)

• Decontamination declaration (

https://www.siemens.com/sc/

declarationofdecontamination

With this declaration you warrant "that the device/replacement part has been carefully
cleaned and is free of residues. The device/replacement part does not pose a hazard for
humans and the environment."
If the returned device/replacement part has come into contact with poisonous, corrosive,
flammable or water-contaminating substances, you must thoroughly clean and
decontaminate the device/replacement part before returning it in order to ensure that all
hollow areas are free from hazardous substances. Check the item after it has been cleaned.
Any devices/replacement parts returned without a decontamination declaration will be
cleaned at your expense before further processing.

Devices described in this manual should be recycled. They may not be dis‐
posed of in the municipal waste disposal services according to the Directive
2012/19/EC on waste electronic and electrical equipment (WEEE).
Devices can be returned to the supplier within the EC, or to a locally ap‐
proved disposal service for eco-friendly recycling. Observe the specific reg‐
ulations valid in your country.
Further information about devices containing batteries can be found at:
Information about battery / product return (WEEE) (

support.industry.siemens.com/cs/document/109479891/

)

9.2

Ordering of spare parts

Ensure that your ordering data is not outdated. The latest ordering data is always available on
the Internet: Process instrumentation catalog (

http://www.siemens.com/

processinstrumentation/catalogs

Service and Maintenance
9.2 Ordering of spare parts

TRANSMAG 2 with MAG 911/E

78

Operating Instructions, 03/2021, A5E00102775-AC

«
...
76
77
78
79
80
...
»

Summary of Contents for SITRANS F TRANSMAG 2































































































































Reviews:

No comments