Siemens SITRANS F MAG 6000 I Operating Instructions Manual Download Page 12

Page: 12 / 104

● Overvoltage category II
● Pollution degree 2

NOTICE
Material compatibility
Siemens Flow Instruments can provide assistance with the selection of wetted sensor

parts. However, the full responsibility for the selection rests with the customer and Siemens

Flow Instruments can take no responsibility for any failure due to material incompatibility.

CE marked equipment

The CE-mark symbolizes the compliance of the device with the following directives:
● EMC-directive 2004/108/EC
● Low voltage directive 2006/95/EC
● Pressure equipment directive (PED/DGRL) 97/23/EC
● ATEX Directive 94/9/EG

2.3

Installation in hazardous area

WARNING

Conditions for safe use
Equipment used in hazardous areas must be Ex-approved and marked accordingly. It is

required that the special conditions for safe use provided in the manual and in the Ex

certificate are followed!

WARNING

Suitable hazardous area approval
Make sure the hazardous area approval is suitable for the environment in which the device

will be installed.

WARNING

"Flameproof enclosure" type of protection
Only open devices with type of protection "Flameproof enclosure" in hazardous areas when

the power to the device is turned off, otherwise there is a risk of explosion.

Safety notes
2.3 Installation in hazardous area

SITRANS MAG 6000 I/6000 I Ex de

Operating Instructions, 08/2018,

A5E02083319-AH

Summary of Contents for SITRANS F MAG 6000 I









































































































Search results

Summary of Contents for SITRANS F MAG 6000 I

Reviews:

Siemens SITRANS F MAG 6000 I, Operating Instructions Manual, Page: 12 / 104

Search results

Summary of Contents for SITRANS F MAG 6000 I

Reviews: