manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 92 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 92

Meter

MAG 8000 Standard

(7ME6810)

MAG 8000 Irrigation

(7ME6880)

MAG 8000 CT

(7ME6820)

Conformity

 

-

-

CEN EN 14154

ISO 4064

PED

97/23EC

-

97/23EC

EMC

EN 61000-6-3

EN 61000-6-2

EN 61326-1

For further features, see "Features" (Page 158).

10.2

Sensor

Technical specifications

Sensor

MAG 8000

(7ME6810)

MAG 8000

(7ME6880)

MAG 8000 CT

(7ME6820)

Size, flange and 

pressure range

EN 1092-1

(DIN 2501)

DN 25 and DN 40: PN 40

DN 50 to 150: PN 16

DN 200 to 1200: PN 10 or 

PN 16

DN 50 to 600:

Drilled flanges 

(maximum pressure 7 bar)

DN 50 to 600: PN 16

ANSI 16.5

Class 150 

lb

1" to 24": 20 bar (290 psi)

2" to 24":

Drilled flanges 

(maximum pressure 7 bar)

2" to 24": 20 bar (290 psi)

AWWA 

C-207

28" to 48": PN 10

-

-

AS 4087

DN 50 to 1200: PN 14

DN50 to DN1200: PN16

DN 50 to 600: PN 16

AS 2091-1

Table D

-

Drilled flanges

(maximum pressure 7 bar)

-

AS 2191

Table E

 

DN25, DN40, DN125

 

Max. excitation fre‐

quency

Basic version

Battery-

powered

1/15 Hz for sensor size 

DN 25 to 150 (1" to 6")

1/30 Hz for sensor size 

DN 200 to 600 (8" to 24")

1/60 Hz for sensor size 

DN 700 to 1200 (28" to 48")

1/15 Hz for sensor size 

DN 25 to 150 (1" to 6")

1/30 Hz for sensor size 

DN 200 to 600 (8" to 24")

1/60 Hz for sensor size

DN 700 to 1200 (28" to 48")

1/15 Hz for sensor size 

DN 50 to 150 (1" to 6")

1/30 Hz for sensor size 

DN 200 to 600 (9" to 24")

Mains-

powered

6.25 Hz for sensor size 

DN 25 to 150 (1" to 6")

3.125 Hz for sensor size 

DN 200 to 600 (8" to 24")

1.5625 Hz for sensor size 

DN 700 to 1200 (28" to 48")

3.125 Hz for sensor size 

DN 25 to 600 (1" to 24")

1.5625 Hz for sensor size

DN 700 to 1200 (28" to 48")

 

6.25 Hz for sensor size 

DN 25 to 150 (1" to 6")

3.125 Hz for sensor size 

DN 200 to 600 (8" to 24")

Technical data
10.2 Sensor

SITRANS MAG 8000

92

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments