manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 91 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 91

Technical data

10

10.1

MAG 8000 water meter

Meter

MAG 8000 Standard

(7ME6810)

MAG 8000 Irrigation

(7ME6880)

MAG 8000 CT

(7ME6820)

Accuracy

Standard calibra‐

tion

± 0.4% of rate ± 2 mm/s ± 0.8% of rate ± 2.5 mm/s

-

Extended calibra‐

tion

± 0.2% of rate ± 2 mm/s

0.4% of rate ± 2.5 mm/s

-

OIML R49 

(DN 50 to DN 600 

(2" to 24"))

-

-

Class 1 and 2 with turn-

down ratio up to

Q3/Q1 = 400 at Q2/Q1 = 

1.6

MI-001 

(DN 50 to DN 600 

(2" to 24"))

-

-

Class 2 with turn-down ra‐

tio 

Q3/Q1 = 250, Q3/Q1 = 

200, Q3/Q1 = 160 at Q2/

Q1 = 1.6

NMI 10

-

±2.5% (Q1 ≤ Q ≤ Q4)

-

Media conductivity  

Clean water > 20 μs/cm

Temperature

Ambient 

−20 to +60 °C

(−4 to +140 °F)

−20 to +60 °C

(−4 to +140 °F)

−20 to +55 °C

(−4 to +131 °F)

Media

0 to 70 °C

(32 to +158 °F)

0 to 70 °C

(32 to +158 °F)

0.1 to 50 °C

(32 to +122 °F)

Storage

−40 to +70 °C

(−22 to +158 °F)

−40 to +70 °C

(−22 to +158 °F)

−40 to +70 °C

(−22 to +158 °F)

Enclosure

 

IP68/NEMA 6P rating.

Cable glands mounted requires Sylgard potting kit to remain IP68/NEMA 6P,

otherwise IP67/NEMA 4 rating is obtained.

Factory mounted cable provides IP68/NEMA 6P rating

Approvals

Drinking water ap‐

provals

NSF 61 (cold water) USA

WRAS (BS 6920 cold wa‐

ter) UK

ACS Listed France

DVGW W270 Germany

Belgaqua (B)

FM Fire Service (Class 

Number 1044)

NSF 61 (cold water) USA

WRAS (BS 6920 cold wa‐

ter) UK

 

CPA (DN 50 to DN 600)

NSF 61 (cold water) USA

WRAS (BS 6920 cold wa‐

ter) UK

ACS Listed France

DVGW W270 Germany

Belgaqua (B)

FM Fire Service (Class 

Number 1044)

 

Custody transfer 

approval

OIML R 49

NMI10 (Australia)

OIML R 49

OIML R 49 MAA

MI-001 (DK-0200-

MI-001-011)

PTB K7.2

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

91

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments