manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 79 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 79

Figure 8-1

Verification sealings

8.5

Power up with battery reset, date and time set up

VHF

!VHF

!VHF

!VHF

1RUHVHW!VHF

1RFKDQJH!VHF

&KDQJH

5HVHW

1H[W

When new batteries have been installed, power-up procedure will enable resetting battery 

capacity and setting up date and time. Battery capacity reset, date and time can also be 

corrected via parameters 508 and 100.
When battery plug is connected, meter will display meter version for 10 seconds. Display will 

then show "rESEt.bAt" indicating the option to reset internal battery power calculation. To 

execute reset, press key within 6 seconds. If key is not pressed, meter will proceed to set date, 

set clock, and finally normal operation mode.
If key is pressed within reset battery time, display will indicate "Accept" to ensure that reset 

should take place. Reset will take place only if key is pressed again within the next 6 seconds. 

If not, normal operation will begin.

Service and maintenance

8.5 Power up with battery reset, date and time set up

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

79

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments