manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 41 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 41

Commissioning

6

The meter can be configured using a PC software package - either SIMATIC PDM or Flow 

Tool.
Both SIMATIC PDM and Flow Tool are software packages for configuring, parameterizing, 

commissioning and maintaining devices (e.g. transducers) and for configuring networks and 

PCs.        
For commissioning via Flow Tool, refer to the appendix "Flow Tool" (Page 115).

6.1

SIMATIC PDM

Among other features, SIMATIC PDM contains a simple monitoring of process values, 

interrupts and status/diagnosis signals of device. This chapter describes how to set up 

SIMATIC PDM and how to configure the device for commissioning.

Note
For instructions on installation and operation of SIMATIC PDM, refer to the SIMATIC PDM 

Getting Started

6.2

Initial commissioning via SIMATIC PDM

This chapter describes how to install the PDM device driver (EDD). The newest EDD driver is 

available on the internet (

http://support.automation.siemens.com/WW/view/en/

19701862/133100

).

Install the EDD files from SIMATIC PDM "Manage Device Catalog" via the following steps:
Windows START menu → program folder "SIMATIC" → SIMATIC PDM → Manage device 

catalog.

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

41

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments