Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 36 | Manualshive

Page: 36 / 164

Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 36

5.4

Outputs

Pulse output connection diagram for MAG 8000

MAG 8000 internal connection

87L166.10.10

①

②

③

Output A
Output B
Passive output - no polarization - open drain

External connection variant

87L167.10.10

4

5

6

6

④

⑤

⑥

Positive pule logic
Negative pulse logic
Signal

Pulse output can be configured as volume, alarm or call-up, see Commissioning (Page 53).
Pulse output is not polarized and can be connected for positive or negative logic.
Pull up/down resistor (R) is selected in relation to power supply voltage (V) and with a max.

current (I) of 50 mA.

Note
Pulse output isolation
The MAG 8000 pulse output has a functional isolation only and must therefore be connected

to equipment complying with the Low Voltage Directive in order to be considered safe.

Connecting
5.4 Outputs

SITRANS MAG 8000

36

Operating Instructions, 11/2018, A5E03071515-AE

«
...
34
35
36
37
38
...
»

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments