manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 33 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 33

5.2

Remote version

Remote installation

MAG 8000 CT user sealing

1. Verify that model and serial numbers shown on labels of sensor and transmitter are 

matched properly.

2. Ensure that cable is safely installed to avoid damage of cable and connectors. Please note 

the different coil and electrode connector types both having a minimum RADIUS of 45 mm 

(1.8 inches); otherwise there s a risk of damaging the cable. Save dust covers for future 

use and protection.

3. Ensure connectors are clean.
4. Ensure connectors are fastened securely to achieve a good connection and watertight seal.

Note
If dirt enters connector ends, use plain water for cleaning. Ensure connectors are completely 

dry before making connections.

For MAG 8000 CT user sealing, see User and verification sealings (Page 81).

Connecting

5.2 Remote version

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

33

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments