manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 32 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 32

5.1

General safety requirements

WARNING

The pertinent regulations must be observed for electrical installation.
● Never install the device with the mains voltage switched on!  
● Danger of electric shock!
● The electrodes and magnetic current line may only be connected when the device is not 

connected to the power supply.

● If the housing is under voltage (power supply), the cover may be unscrewed by qualified 

personnel only.

WARNING

Mains supply from building installation Class II  
A switch or circuit breaker (max. 15 A) must be installed in close proximity to the equipment 

and within easy reach of the operator. It must be marked as the disconnecting device for the 

equipment.

Connecting
5.1 General safety requirements

SITRANS MAG 8000

32

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments